BREEAM credits for plywood sit in two places: Mat 03 responsible sourcing, where FSC or PEFC chain of custody scores, and Hea 02 indoor air quality, where a formaldehyde test report scores. LEED points follow the same split. Minh Thanh Plywood shows which document wins each credit, checked 20 October 2026.
What are BREEAM credits?
BREEAM credits are the points a building earns in ten weighted categories of the BREEAM assessment: Management, Health and Wellbeing, Energy, Transport, Water, Materials, Waste, Land Use and Ecology, Pollution, and Innovation. The weighted percentage sets the rating, and minimum standards in some credits must be met for each rating.
| BREEAM rating | Weighted score |
|---|---|
| Outstanding | 85% or more |
| Excellent | 70% or more |
| Very Good | 55% or more |
| Good | 45% or more |
| Pass | 30% or more |
| Unclassified | Below 30% |
The thresholds above apply to BREEAM UK New Construction 2018 and the International schemes. BRE’s BREEAM pages, checked on 20 October 2026, list the current schemes. New Construction Version 7 was launched in 2025, and registrations for BREEAM International New Construction version 6 closed on 27 January 2026. Credit names stay the same across versions; the weightings and criteria change.

BREEAM schemes: where plywood credits apply
BREEAM has six schemes, and plywood credits matter most in the two that buy new materials: New Construction and Refurbishment and Fit Out. BREEAM has certified buildings since 1990, and BRE Global is accredited by UKAS against BS EN ISO/IEC 17065 for product certification activities, as BREEAM states, checked on 21 October 2026.
| BREEAM scheme | Version on the BREEAM standards page, 21 October 2026 | Plywood credits relevant? |
|---|---|---|
| New Construction | Version 7, with V7.1 published | Yes: Mat 03 sourcing, Hea 02 emissions, EPD credits |
| New Construction Residential | Homes and flats | Yes: same sourcing and emission evidence |
| Refurbishment and Fit Out | Version 7, registrations open | Yes: new linings, joinery and fit-out panels |
| In-Use | Existing assets in operation | Limited: assesses operation, not purchasing of new panels |
| Communities | Masterplans | Limited: masterplan level, not product level |
| Infrastructure | Civil works | Limited: plywood appears as formwork or temporary works |
Category weightings differ by scheme and version, and Materials and Health and Wellbeing each carry a share of the weighted score; read the weightings in the manual the project is registered under rather than a table from another version. The evidence a plywood supplier sends is the same across the schemes marked Yes.
Which BREEAM credits can plywood support?
Plywood supports four BREEAM credits: Mat 03 responsible sourcing, Hea 02 indoor air quality, and Mat 01 and Mat 02 when the product has an Environmental Product Declaration (EPD). Mat 03 and Hea 02 are where plywood usually scores, because they need documents most mills can supply.
| BREEAM credit | What it rewards | The plywood document that scores |
|---|---|---|
| Mat 03 Responsible sourcing (prerequisite) | All timber legally harvested and traded | Legality evidence: EUDR or UKTR due diligence file, origin records |
| Mat 03 Responsible sourcing (credits) | Products from certified responsible sourcing schemes | FSC or PEFC chain-of-custody certificate, claim on the invoice |
| Hea 02 Indoor air quality | Low-emitting products in the building | Formaldehyde emission test report from an accredited laboratory |
| Mat 01 / Mat 02 Life cycle impacts | Lower embodied impact, products with EPDs | EPD to EN 15804 |
A BREEAM assessor reviews evidence product by product, so each document must name the product, the manufacturer and, for chain of custody, the claim on the invoice that covers the delivered lot.

Mat 03: responsible sourcing of plywood
Mat 03 has a prerequisite and a scoring part. The prerequisite is that all timber and timber-based products on the project are legally harvested and traded; the scoring part rewards products bought under recognised responsible sourcing schemes, with FSC and PEFC chain of custody at the top of the BREEAM scheme table.
Three documents settle Mat 03 for plywood:
- Legality. The due diligence file the importer keeps under the EU Deforestation Regulation (Regulation (EU) 2023/1115) or the UK Timber Regulation. Minh Thanh supplies the EUDR compliance dossier (origin records and geolocation files) with orders.
- Chain of custody. The supplier’s FSC or PEFC certificate code, checkable on the FSC public certificate search, and the FSC claim printed on the invoice line.
- Scope. A certificate that covers plywood and the legal entity on the invoice. A trader’s certificate does not cover the press line that made the panel.
FSC-certified plywood from Minh Thanh is available*. Our FSC plywood guide explains the claims and how they appear on invoices.
*Supplied directly or through qualified partner mills.
Hea 02: indoor air quality and formaldehyde
Hea 02 scores when the products specified for the inside of the building meet emission limits, tested by an accredited laboratory to the method the manual names. For wood-based panels such as plywood, the limit that matters is formaldehyde.
Manufacturers’ BREEAM data sheets quote the Hea 02 product criterion for wood-based products as formaldehyde below 0.06 mg/m³ in a chamber test, alongside limits for total volatile organic compounds and carcinogens. BREEAM’s knowledge base also accepts factory production control testing for some products, and exempts panels made without formaldehyde-containing materials from formaldehyde testing.
For a plywood specification, three points decide whether Hea 02 is met:
- Method. EN 717-1 chamber testing is the European reference method; other chamber methods need the assessor’s acceptance.
- Laboratory. Accredited, with a report that names the product and its thickness.
- Scope. Every wood-based product inside the building, including the core of a laminated panel.
Minh Thanh panels for European furniture buyers use UF glue at E0 emission. Third-party testing to EN 717-1 is arranged through SGS on request, which gives the assessor a report on the method BREEAM names.
Do plywood products count toward LEED credits?
Yes. Plywood counts toward two LEED v4.1 credits: Building Product Disclosure and Optimization, Sourcing of Raw Materials (wood products certified by FSC), and Low-Emitting Materials (composite wood with documented low formaldehyde emissions). An EPD adds a third route.
| LEED v4.1 credit | What plywood contributes | The plywood document that counts |
|---|---|---|
| MR: Sourcing of Raw Materials | FSC wood at 100% of its cost; 1 point at 15% of product cost from three manufacturers, 2 points at 30% from five | FSC 100% or FSC Mix Credit claim on the invoice, CoC code |
| EQ: Low-Emitting Materials, composite wood | Panels documented as low formaldehyde | TSCA Title VI ULEF or NAF certificate, or EN 717-1:2014 test to class E1 |
| MR: Environmental Product Declarations | Products with a product-specific or industry EPD | EPD to ISO 14025 / EN 15804 |
The thresholds come from the USGBC credit library, checked 20 October 2026, and FSC US’s green building guidance on how FSC wood is valued at full cost.
Low-Emitting Materials: what LEED reviewers accept for plywood
LEED v4.1 accepts composite wood such as plywood when its formaldehyde emission is documented one of three ways: certified TSCA Title VI ULEF (ultra-low-emitting formaldehyde), certified TSCA Title VI NAF (no added formaldehyde), or tested to EN 717-1:2014 and meeting emission class E1.
Reviewers have rejected a plain TSCA Title VI certificate as proof, because every hardwood plywood panel sold in the US must already meet TSCA Title VI. The credit asks for the stricter ULEF or NAF designation, or the EN 717-1 alternative. The underlying rule sets 0.05 ppm for veneer-core hardwood plywood under EPA’s formaldehyde emission limits.
Minh Thanh is CARB P2 / TSCA Title VI certified (ICTT mill no. 23024). Six ASTM D6007 chamber tests between April 2025 and June 2026 on 9, 15 and 18 mm panels averaged 0.014–0.032 ppm. For a LEED project, we pair that certificate with an SGS test to EN 717-1, which documents the class E1 route. Our NAF and low-formaldehyde plywood guide explains the ULEF and NAF labels.

Credit-by-credit: which plywood document wins each credit
Each green building credit needs a specific plywood document, and the same panel scores or fails by its paperwork. The table below joins both schemes, so one request to the mill covers a project that is assessed under BREEAM and LEED.
| Credit | Scheme | Document | Minh Thanh supplies |
|---|---|---|---|
| Mat 03 prerequisite | BREEAM | Legal timber evidence | EUDR compliance dossier with orders |
| Mat 03 credits | BREEAM | FSC or PEFC CoC certificate, claim on invoice | FSC available* |
| Hea 02 | BREEAM | Formaldehyde test, accredited lab | SGS test to EN 717-1 on request |
| Sourcing of Raw Materials | LEED v4.1 | FSC claim on invoice | FSC available* |
| Low-Emitting Materials | LEED v4.1 | TSCA Title VI ULEF / NAF, or EN 717-1 class E1 | TSCA Title VI certificate, chamber reports, SGS EN 717-1 test |
| EPD credits | Both | Product-specific or industry EPD | Product data for the EPD author |
Packaging also enters some site waste and materials discussions. Minh Thanh packaging was tested by SGS in September 2026 under Regulation (EU) 2025/40: lead, cadmium, mercury and hexavalent chromium were not detected in the cardboard, plywood and pallet blocks, strapping band and wrapping film, a PASS against the 100 mg/kg limit.

Which documents does a BREEAM assessor need for plywood?
A BREEAM assessor needs three plywood documents: legality evidence for the Mat 03 prerequisite, a chain-of-custody certificate with the invoice claim for the Mat 03 credits, and a formaldehyde test report for Hea 02. Each one must name the product the contractor actually installed.
- Product data sheet. Panel build, face and core species, glue type and thickness.
- Legality file. Species, country of harvest and the due diligence statement or reference.
- Chain-of-custody certificate. The code, scope and validity, plus the invoice line carrying the claim.
- Emission report. Laboratory, method (EN 717-1), result, product and thickness tested.
- Delivery note. Links the delivered lot to the invoice and certificate.
Collect the set at the order stage, not at handover. A contractor who asks for an FSC claim after the plywood is installed cannot add it to an invoice already issued.

Why emissions data matters for plywood in green buildings
Emissions data matters because plywood is installed inside the building envelope in large areas (wall linings, furniture, flooring underlay, joinery), and formaldehyde is the indoor air pollutant both schemes test for in wood panels. A building with one untested panel type can lose the credit.
Glue type and emission class are two separate specifications. Furniture plywood uses UF glue at E0 emission; exterior plywood uses melamine-fortified or phenolic (WBP) bonds. The emission class is set by the resin system and pressing, and it is proven by a test report, not by the glue name. Our guide Is plywood toxic? covers formaldehyde in indoor use.
How to specify plywood for a BREEAM or LEED project
Specify plywood for a BREEAM or LEED project by writing the credit evidence into the product specification, so the documents arrive with the panels. Five lines cover both schemes.
- Use and location. Interior lining, furniture, joinery or structural.
- Sourcing. “FSC Mix Credit or FSC 100% claim on the invoice, CoC code stated.”
- Emission. “Formaldehyde to EN 717-1, class E1 or lower, accredited laboratory report”, plus “TSCA Title VI certified” for LEED.
- Legality. “EUDR compliance dossier with the order” for EU projects.
- Build. Face, core, glue, thickness and tolerance.
Writing the evidence into the specification keeps the subcontractor from buying an equivalent panel without the documents.
Is all plywood suitable for green building procurement?
No. Plywood is suitable for green building procurement only when it comes with the documents the credits need: a chain-of-custody claim for sourcing credits and an emission report for air quality credits. Two identical panels, one with documents and one without, score differently.
The build still matters for performance. Minh Thanh furniture panels are pressed twice as standard (core board pressed and calibrated, then face and back pressed on), with core layers stitched horizontally and vertically, thickness tolerance down to ±0.2 mm, and veneers and panels dried to 8–12 % moisture content at dispatch. Flat, calibrated panels cut waste on site, which some site waste plans record.
What Minh Thanh Plywood can supply for green building projects
Minh Thanh Plywood, a manufacturer in Ha Hoa, Phu Tho, Vietnam, with 50,000+ m³ of annual capacity, supplies furniture and interior plywood with the documents green building credits need.
- Emission: CARB P2 / TSCA Title VI certified (ICTT mill no. 23024); six chamber tests averaging 0.014–0.032 ppm, three by Shanghai Hongjun and three by ICTT Vietnam; EN 717-1 testing through SGS on request.
- Legality: EUDR compliance dossier (origin records and geolocation files) with orders; plantation timber cores of Styrax and Eucalyptus.
- Chain of custody: FSC available*.
- Quality system: ISO 9001:2015 for plywood manufacturing (KAC25/0185); TCVN 11902:2017 (VietCert 141.1-VNC-HC).
- Packaging: SGS PPWR test, September 2026, PASS.
See the furniture plywood range for faces, cores and sizes. For destination rules beyond green building, read our plywood certification map by destination.
*Supplied directly or through qualified partner mills.
What to send for a green building plywood quote
Send the credits the plywood must support with the specification, and we quote the panel and the documents together.
- Application: interior lining, furniture, joinery or shopfitting.
- Core: Styrax or Eucalyptus; stitched.
- Glue and emission: UF glue at E0 emission, plus the test method the assessor needs (EN 717-1).
- Face: species and grade pair, sanded, UV-ready if you coat.
- Size and thickness: 1220 × 2440 or 1250 × 2500 mm, thickness and tolerance.
- Credits and documents: BREEAM Mat 03 and Hea 02, LEED sourcing and low-emitting materials; FSC claim required or not.
Write to contact@minhthanhplywood.com or WhatsApp +84 988 586 601 (Lisa). We reply within hours, and free samples are available for the project’s own tests.
Buyer questions, answered
Does plywood count toward LEED credits?
Yes. Plywood counts toward LEED v4.1 Sourcing of Raw Materials when it carries an FSC claim on the invoice, and toward Low-Emitting Materials when its formaldehyde emission is documented as TSCA Title VI ULEF or NAF, or EN 717-1 class E1.
Which documents does a BREEAM assessor need for plywood?
For Mat 03, proof of legal timber and, to score, the FSC or PEFC chain-of-custody certificate with the claim on the invoice. For Hea 02, a formaldehyde emission test report to the method the manual names, from an accredited laboratory.
What are BREEAM credits?
BREEAM credits are points awarded in ten categories, from Management to Pollution, each weighted. The weighted score sets the rating: Pass from 30%, Good 45%, Very Good 55%, Excellent 70% and Outstanding 85%.
How many BREEAM credits does plywood affect?
Plywood alone moves a few credits: Mat 03 sourcing, Hea 02 product emissions, and Mat 01 or Mat 02 when an EPD is available. It contributes to those credits together with the other products specified.
Is TSCA Title VI compliance enough for LEED?
LEED v4.1 reviewers ask for TSCA Title VI ULEF or NAF certification, or an EN 717-1 test showing class E1. A TSCA Title VI certificate plus an EN 717-1 report to E1 is the safe pair.
Does FSC plywood earn LEED points?
FSC-certified wood products, invoiced with an FSC 100% or FSC Mix Credit claim, count at 100% of their cost toward LEED Sourcing of Raw Materials. The credit needs 15% by cost from three manufacturers for one point.
What formaldehyde level does BREEAM accept for wood panels?
BREEAM product emission criteria quoted in manufacturers' BREEAM data sheets set formaldehyde below 0.06 mg/m³ by chamber test for wood-based products. Check the manual version the project is registered under.
Can Minh Thanh supply FSC plywood for a BREEAM project?
Yes. FSC-certified plywood is available*, supplied directly or through qualified partner mills. Every order also comes with the EUDR compliance dossier, which supports the Mat 03 legality prerequisite.
What should buyers request first?
Ask the project team which credits the plywood must support, then request the matching documents: the chain-of-custody certificate number, the emission certificate and test report, and an EPD if the LCA credit is targeted.
Is all plywood suitable for green building procurement?
No. Plywood without a chain-of-custody claim scores nothing in Mat 03 or LEED sourcing, and plywood without an emission report scores nothing in Hea 02 or Low-Emitting Materials, even if the panel itself is identical.